201 Nickel Alloy Coil
CURRENT POSITION：
201 Nickel Alloy Coil
CONTACT US
WhatsApp/WeChat/Mobile：+86 13563560199
Message
201 NICKEL ALLOY COIL PRODUCT INTRODUCTION
Nickel 201 is an extremely low carbon commercial pure nickel approved for use in high-temperature environments up to 1230℃. Excellent plasticity and toughness, high chemical stability. Pure nickel is resistant to atmospheric, alkali and fresh water corrosion. It has excellent corrosion resistance in hot concentrated alkaline solution, medium and slightly acidic solution, organic solvent and other media. Not resistant to oxidizing acids and solutions containing oxidants and most molten metals. Sulfidation brittleness also occurs in high temperature sulfurous gases.
201 NICKEL ALLOY COIL PRODUCT SPECIFICATION
201 NICKEL ALLOY COIL PRODUCT DISPLAY
201 NICKEL ALLOY COIL PRODUCT COMPOSITION
201 NICKEL ALLOY COIL PRODUCT DETECTION
201 NICKEL ALLOY COIL PACKAGE DELIVERY
20ft GP:5898mm(Length)x2352mm(Width)x2393mm(High)
40ft GP:12032mm(Length)x2352mm(Width)x2393mm(High)
40ft HC:12032mm(Length)x2352mm(Width)x2698mm(High)
Standard export packing wooden pallet, wooden case, etc. (inside: waterproof paper, outside: steel belt and pallet)
PRODUCT RECOMMEND
270 Nickel Alloy BarPure nickel Ni270 nickel is mainly used in reducing media and has good corrosion resistance in acidic and alkaline environments. The biggest characteristic of Nickel270 nickel alloy is the corrosion resistance of alkaline medium, such as caustic potash, caustic soda, etc., has been widely used in ionic membrane caustic soda process. Nickel has good corrosion resistance to dry fluoride. Nickel2 alloy has also been successfully used in dry chlorine and hydrogen chloride from room temperature to 540℃. It can also be used in a stationary hydrofluoric acid solution.- 201 Nickel Alloy BarNickel 201 Round Bar can be found in hardened and tempered form. It is a commercially unalloyed nickel that has excellent corrosion resistance and has a very low electrical resistivity. It also possesses other features like weldability, formability and high tensile strength. The nickel used in Nickel 201 Rod products are 99.96 % pure. The Nickel 201 Bar is used for a number of processing equipments, most importantly to maintain purity of products in handling foods, alkalies and synthetic fibers
- 200 Nickel Alloy BarNickel Round Bar/Rod 200 is normally used for chemical, food and beverage, and ornamental applications. 200 nickel offers the highest corrosion resistance as well as high formability, weldability and conductivity.
- 201 Nickel Alloy PlateNickel 201 is an extremely low carbon commercial pure nickel approved for use in high-temperature environments up to 1230℃. Excellent plasticity and toughness, high chemical stability. Pure nickel is resistant to atmospheric, alkali and fresh water corrosion. It has excellent corrosion resistance in hot concentrated alkaline solution, medium and slightly acidic solution, organic solvent and other media. Not resistant to oxidizing acids and solutions containing oxidants and most molten metals. Sulfidation brittleness also occurs in high temperature sulfurous gases.
Nickel 200/201 plate combines good mechanical properties with excellent resistance to many corrosive environments. Nickel 201, the lower carbon chemistry, is preferred for service in temperatures above 600°F (315°. C). Nickel 200 and 201 plate offer outstanding corrosion resistance to caustic soda and other alkalis. - 200 Nickel Alloy PlateNickel Sheet/Plate 200 is normally used for chemical, food and beverage, and ornamental applications. 200 nickel offers the highest corrosion resistance as well as high formability, weldability and conductivity.
- 270 Nickel Alloy PlatePure nickel Ni270 nickel is mainly used in reducing media and has good corrosion resistance in acidic and alkaline environments. The biggest characteristic of Nickel270 nickel alloy is the corrosion resistance of alkaline medium, such as caustic potash, caustic soda, etc., has been widely used in ionic membrane caustic soda process. Nickel has good corrosion resistance to dry fluoride. Nickel2 alloy has also been successfully used in dry chlorine and hydrogen chloride from room temperature to 540℃. It can also be used in a stationary hydrofluoric acid solution.
- 200 Nickel Alloy CoilThe Nickel 200 coils and sheets have an enhance resistance to creep and are incredibly ductile and powerful. Since the nickel 200 sheets plates and coils have a superior corrosion resistance power, they have higher temperature strength in comparison with the common alloy sheets and coils.
- 270 Nickel Alloy CoilPure nickel Ni270 nickel is mainly used in reducing media and has good corrosion resistance in acidic and alkaline environments. The biggest characteristic of Nickel270 nickel alloy is the corrosion resistance of alkaline medium, such as caustic potash, caustic soda, etc., has been widely used in ionic membrane caustic soda process. Nickel has good corrosion resistance to dry fluoride. Nickel2 alloy has also been successfully used in dry chlorine and hydrogen chloride from room temperature to 540℃. It can also be used in a stationary hydrofluoric acid solution.
- 201 Nickel Alloy CoilNickel 201 is an extremely low carbon commercial pure nickel approved for use in high-temperature environments up to 1230℃. Excellent plasticity and toughness, high chemical stability. Pure nickel is resistant to atmospheric, alkali and fresh water corrosion. It has excellent corrosion resistance in hot concentrated alkaline solution, medium and slightly acidic solution, organic solvent and other media. Not resistant to oxidizing acids and solutions containing oxidants and most molten metals. Sulfidation brittleness also occurs in high temperature sulfurous gases.
- 270 Nickel Alloy PipePure nickel Ni270 nickel is mainly used in reducing media and has good corrosion resistance in acidic and alkaline environments. The biggest characteristic of Nickel270 nickel alloy is the corrosion resistance of alkaline medium, such as caustic potash, caustic soda, etc., has been widely used in ionic membrane caustic soda process. Nickel has good corrosion resistance to dry fluoride. Nickel2 alloy has also been successfully used in dry chlorine and hydrogen chloride from room temperature to 540℃. It can also be used in a stationary hydrofluoric acid solution.
- 201 Nickel Alloy PipeNickel 201 Pipe is a commercially pure nickel alloy with minimum 99% nickel in the composition. It has similar properties of the Nickel 200 alloy but has less carbon content. The reduction of carbon content makes it good for welding and avoids intergranular corrosion. Also, the need for slug removal after welding is greatly reduced. The Alloy 201 Seamless Pipes are wrought nickel and it has less absolute roughness and is very precise in its dimensions. The ASTM B161 UNS N02201 Welded Pipes belongs to the standard which governs the pipe ranging up to 10 inches. The wall thickness varies depending on the diameter of the pipe up to 219mm. The diameter and the wall thickness define the schedules and the pressure classes. The Nickel 201 Seamless Pipes are high temperature resistant and corrosion resistant. It is particularly resistant to alkalis. And this property makes it used in chemical industries and food processing industries.
- 200 Nickel Alloy PipeAlloy 200 nickel pipe is made from commercially pure wrought nickel, with good mechanical properties, excellent resistance to many corrosives. Typical applications include a variety of processing equipment, particularly to maintain product purity in handling foods, synthetic fibers, and alkalies.
- Gr7 Titanium Alloy BarMany good qualities are found in the Titanium Gr 7 bar and that has become possible by using excellent quality of alloy only while fabricating it. The bars are having attributes like high tensile strength, good dimensional accuracy, good surface finishes, high durability, flexibility, hardness, long-lasting, withstanding heavier loads etc. Also, it is having a high ability to be excellently resistance to general corrosion, crevice corrosion, pitting resistance, oxidation resistance, abrasion/erosion resistance etc.
- Gr2 Titanium Alloy BarTitanium Round Bar/Rod Grade 2 is normally used for aerospace, automotive, medical, cryogenic, and thermal applications. Grade 2 titanium offers high corrosion resistance and the approximate strength of 6061-T6 aluminum. It's high strength, low weight ratio give it a diversified range of uses. Grade 2 titanium round bar/rod stock is available in full size and custom cut lengths.
- Gr3 Titanium Alloy BarTitanium Gr.3 Round Bars has very high tensile strength and toughness (even at extreme temperatures). DIN 3.7055 Round Bars is least used of the commercially pure titanium grades, but that does not make it any less valuable. Grade 3 Titanium Round Bars is stronger than Grades 1 and 2, similar in ductility and only slightly less formable - but it possesses higher mechanicals than its predecessors. UNS R50550 Round Bars are used for corrosion resistance applications where cost, ease of fabrication, and welding are important. Ti Grade 3 Round Bars is high strength Titanium, which is generally used for Matrix-plates in shell and tube heat exchangers. Titanium Alloy Gr. 3 Round Bars is also often used in Orthopaedic applications, Needles, Pacing leads, Woven wire mesh, Sutures, Ligature clips, Orthodontic appliances, Eye glass frames, and more.
- Gr12 Titanium Alloy BarTitanium is a highly reactive material with a high affinity for oxygen, forming a highly adherent skin and stability. The Titanium Grade 12 Bar is extensively used in chemical processing industries, basically used for the fittings and piping, reactor autoclaves, heat exchangers, valves, and condensers. Jaiman Metalloys LLP supplies the titanium grade 12 bar, sheet, plate, road, welded pipes, welded tubes, forgings, and forging billet. Titanium products like Titanium Grade 12 Bar and Titanium Grade 12 Sheets are highly resistant to crevice corrosion in hot brines.
- Gr9 Titanium Alloy BarTitanium Grade 9 has medium strength that falls between Grade 4 and Grade 5. It has excellent corrosion resistance and is used in Aerospace and Industrial applications. Grade 9 Titanium can be used at higher temperatures than Grades 1 through 4. Grade 9 titanium has good cold rolling properties.
- Gr1 Titanium Alloy BarTitanium Gr.1 Round Bars is one of the softest and most ductile grades exhibiting the greatest formability. DIN 3.7025 Round Bars is the softest and most ductile of these grades. UNS R50250 Round Bars offers optimum ductility and cold formability with useful strength, high-impact toughness, and excellent weldability. Ti Gr. 1 Round Bars is a good solution for cold forming and corrosive environments. The cold work characteristics of Ti Gr. 1 Bars are similar to that of a moderately tempered austenitic stainless steel. CP Titanium Grade 1 Round Bars is often used in airframe components, cryogenic vessels, heat exchangers, CPI equipment, condenser tubing, pickling baskets. Titanium Alloy Gr. 1 Round Bars also offers a higher strength-to-weight ratio and increased corrosion resistance compared to the stainless steel alloys, thus making it an attractive choice for medical applications.
- Ti-6al-4v (TC4) Titanium Alloy BarTi-6al-4v (TC4) titanium alloy is a duplex alloy, with good comprehensive properties, good microstructure stability, good toughness, plasticity and high temperature deformation properties, can be better hot pressure processing, quenching, aging to strengthen the alloy. The strength after heat treatment is about 50% ~ 100% higher than that after annealing. High strength at high temperature, can work at 400℃ ~ 500℃ temperature for a long time, its thermal stability is inferior to α titanium alloy
- Ti-6al-4v (TC4) Titanium Alloy PlateTi-6al-4v titanium alloy, belonging to (A + B) type titanium alloy, has good comprehensive mechanical properties. Greater than strength. The strength sb=1.012GPa, density G =4.4*103 and specific strength Sb/G =23.5 of Ti-6Al-4V, while the specific strength Sb/G of alloy steel is less than 18. Titanium alloy has low thermal conductivity. The thermal conductivity of titanium alloy is 1/5 of iron and 1/10 of aluminum, and the thermal conductivity of TC4 is L =7.955W/m·K. Titanium alloy has low elastic modulus. The elastic modulus E=110GPa of Ti-6Al-4V is about half that of steel. Titanium alloy is prone to deformation in the process of machining. The surface modification of Ti-6Al-4V(TC4) and Ti-5Al-2.5Sn(TA7) titanium alloys was carried out by two injection methods. The experimental results show that the microhardness of titanium alloy is improved, the sliding friction coefficient is significantly reduced, and the wear resistance is effectively improved after ion implantation
- Gr9 Titanium Alloy PlateTitanium Gr 9 Sheets & Plates can be availed via variant hardness ranges as hard, soft, half-hard, quarter-hard, spring-hard, etc. Also, it comes in a diverse range of types like plain sheets, shim sheets, chequered plates, flats, etc. Besides, it also upholds the assortment of finishing works as hot rolled plates, cold rolled sheets, 2B, 2D, BA, SATIN, etc.
Grade 9 has large applications in the sugar industries, oil & gas industries, petrochemical, and power plant industries. It is effortlessly usable and thus it is also seen in the area of fertilizers, chemical processors, pharmaceuticals, food, and dairy industries. Moreover, they are not left behind in nuclear power plants. - Gr7 Titanium Alloy PlateTitanium Gr 7 Sheet & Plate are very useful in high industries applications including high pressure applications such as in nuclear power plants and heat exchangers etc. the company provide the titanium sheets and plates according to the customers requirement.
Talking about its quality, industry provides with various features for titanium Gr 7. These features are; resistant to corrosion, rust proof finishing of the material etc. other features for Titanium Gr 7 Sheet & Plate is useful to sustain in high pressure and temperature environment. The properties also include excellent ductility of the material, its outstanding weldability and toughness. Titanium Gr 7 Sheet & Plate consist of accurate weight ratio as compared with other titanium grades. These qualities make the supply and demand of material high. - Gr3 Titanium Alloy PlateGrade 3 Titanium Sheet is a commercially pure form of titanium. CP (Commercially Pure) Titanium Grade 3 Flat Sheet is unalloyed titanium providing higher mechanical strength (typical yield strength 462 MPa) compared with CP Grades 1 Ti Plate and Ti Grade 2 Sheet. CP Grade 3 Titanium Plate has moderate ductility, excellent weldability and superior corrosion resistance. CP Grade 3 Titanium Sheet again promotes versatility of use and with higher mechanical strength, is used in industrial applications where improved mechanical properties are required. Titanium Cp Grade 3 Strip are suitable for a large variety of chemical and marine as well as aerospace and medical applications where strength is a consideration. Titanium Grade 3 Rolling Sheets is an unalloyed, high strength, titanium product providing excellent corrosion resistance and good weldability. unalloyed UNS R50550 Ti Grade 3 Sheet, CP Grade 3 Titanium Sheet can be cold formed by standards methods.
- Gr1 Titanium Alloy PlateTitanium Alloy Grade 1 Plates is the common high strength and light weight alloy, which is heat treatable and has high strength and ductility along with good weldability and fabricability.
Titanium Gr 1 Sheets & Plates is one of the commonly used among all available titanium alloy and is also called as the titanium alloys workhorse. Ti Gr 1 plate is one of the most comply utilized alloy worldwide wherein the alpha-beta alloy is termed as the titanium industry workhorse alloy. The annealing temperature of the Ti Gr 1 sheet is ranging from 700-785 deg C. Ti Gr 1 plate is having very good tensile attributes at the ambient temp and that is advantageous for creep resistance to 300 deg C. - Gr2 Titanium Alloy PlateTitanium Grade 2 Plate is a commercially pure which contains 99% of minimum titanium. It is corrosion resistance comes from a strongly follower, protective oxide feature, stable which forms in the presence of oxygen. This feature makes it resistant to most oxidizing, neutral and inhibited reducing, as well as mildly reducing environments.
titanium grade 2 sheet provides excellent resistance to marine atmosphere and seawater corrosion. Its corrosion resistance is similar between the four C.P. grades, but mechanical properties differ along with differing iron and oxygen contents. - Gr12 Titanium Alloy PlateGr12 titanium molybdenum nickel alloy nominal composition is Ti-0.3Mo-0.8Ni, is the mid-1970s in the United States research and development of Ti-12 alloy, is a crack corrosion resistant titanium alloy, the alloy at 300℃ tensile strength is twice as high as pure titanium, corrosion resistance of reducing medium significantly improved, Crevice corrosion does not occur in chlorides at 150-200℃.
- Ti-6al-4v (TC4) Gr7 Titanium Alloy CoilTi-6al-4v (TC4) titanium alloy is a duplex alloy, with good comprehensive properties, good microstructure stability, good toughness, plasticity and high temperature deformation properties, can be better hot pressure processing, quenching, aging to strengthen the alloy. The strength after heat treatment is about 50% ~ 100% higher than that after annealing. High strength at high temperature, can work at 400℃ ~ 500℃ temperature for a long time, its thermal stability is inferior to α titanium alloy
- Gr7 Titanium Alloy CoilGr7 alloy is mainly used in dilute hydrochloric acid, dilute sulfuric acid and dilute phosphoric acid environment. It is also widely used in titanium equipment to prevent crevice corrosion, such as tubular heat exchanger and spinning spinneret.
Gr7 titanium alloy is an alloy with excellent corrosion resistance to acid medium formed by adding a small amount of precious metal Pd into pure titanium. The presence of non-toxic by-elements Al and V will become a high-quality material to replace pure titanium and Ti-6Al-4V for biomedical implantation. - Gr9 Titanium Alloy CoilGr9 titanium alloy is a low alloyed near α titanium alloy, the alloy has good cold forming and welding properties, room temperature strength is 20%~50% higher than industrial pure titanium, has good corrosion resistance in many media. Therefore,Gr9 titanium alloy with its excellent comprehensive performance becomes the most suitable for the production of aircraft high pressure resistant lightweight conduit ideal material
- Gr1 Titanium Alloy CoilGr1 titanium alloy has excellent stamping performance. Various forms of welding, good welding performance, welding joints can reach 90% of the strength of the matrix metal. Easy to saw and grinding wheel cutting, good machining performance. Excellent corrosion resistance for parts under 350℃, small force and stamping into a variety of complex shapes of parts. Such as thermal power plant condenser; Piping systems, valves and pumps corroded by Marine seawater; Chemical heat exchanger, pump body, distillation tower; Seawater desalination system, platinum-plated anode; An airplane skeleton, skin, engine parts, beams, etc.
- Gr2 Titanium Alloy CoilTitanium Grade 2 Sheets plates coils have some of the great features to provide like light weight, hard wearing as well as soaring tensile potency. Jaiman provides you such materials in different shapes and sizes. The sheets, plates, coils are being used in chemical processing, architecture, automotive, desalination, automotive, medical, power generation, marine, and chlorate manufacturing.
- Gr3 Titanium Alloy CoilGr3 titanium alloy has excellent stamping performance. Various forms of welding, good welding performance, welding joints can reach 90% of the strength of the matrix metal. Easy to saw and grinding wheel cutting, good machining performance. Excellent corrosion resistance for parts under 350℃, small force and stamping into a variety of complex shapes of parts. Such as thermal power plant condenser; Piping systems, valves and pumps corroded by Marine seawater; Chemical heat exchanger, pump body, distillation tower; Seawater desalination system, platinum-plated anode; An airplane skeleton, skin, engine parts, beams, etc.
- Gr12 Titanium Alloy CoilGr12 titanium molybdenum nickel alloy nominal composition is Ti-0.3Mo-0.8Ni, is the mid-1970s in the United States research and development of Ti-12 alloy, is a crack corrosion resistant titanium alloy, the alloy at 300℃ tensile strength is twice as high as pure titanium, corrosion resistance of reducing medium significantly improved, Crevice corrosion does not occur in chlorides at 150-200℃.
- Gr7 Titanium Alloy PipeGr7 titanium alloy is mainly used in dilute hydrochloric acid, dilute sulfuric acid and dilute phosphoric acid environment. It is also widely used in titanium equipment to prevent crevice corrosion, such as tubular heat exchanger and spinning spinneret.
Gr7 titanium alloy is an alloy with excellent corrosion resistance to acid medium formed by adding a small amount of precious metal Pd into pure titanium. The presence of non-toxic by-elements Al and V will become a high-quality material to replace pure titanium and Ti-6Al-4V for biomedical implantation. - Gr9 Titanium Alloy PipeGr9 titanium alloy is a low alloyed near α titanium alloy, the alloy has good cold forming and welding properties, room temperature strength is 20%~50% higher than industrial pure titanium, has good corrosion resistance in many media. Therefore,Gr9 titanium alloy with its excellent comprehensive performance becomes the most suitable for the production of aircraft high pressure resistant lightweight conduit ideal material
- Gr12 Titanium Alloy PipeTitanium Grade 12 Tubes can withstand cool/wet and dry/hot acid gas loading. It is suitable for laying and coiling onto the seabed. It has a feature of low modulus, fatigue resistance, and greater fracture toughness.
- Ti-6al-4v (TC4) Titanium Alloy PipeTi-6al-4v (TC4) titanium alloy is a duplex alloy, with good comprehensive properties, good microstructure stability, good toughness, plasticity and high temperature deformation properties, can be better hot pressure processing, quenching, aging to strengthen the alloy. The strength after heat treatment is about 50% ~ 100% higher than that after annealing. High strength at high temperature, can work at 400℃ ~ 500℃ temperature for a long time, its thermal stability is inferior to α titanium alloy
